Get Offer

 

 

What're your insights and beliefs about How to Install a Bathtub Yourself?

Mounting a bathtub isn't specifically rocket science, yet it does call for solid plumbing, woodworking, and occasionally, tiling skills. Replacing an old tub with a new one is likewise a moderately tough project. If the old bathtub is readily easily accessible, the task can move quickly; if you need to open a wall to get rid of the old tub and also place the new bath tub, the task is a lot harder. In either situation, the project is within a residence handyman's skills, although you will require a helper to vacate the old tub and also set in the new one. Ensure you have actually qualified on your own for the task as well as are comfortable trying it. Instead of hiring a contractor to take over a halfway-completed task, it is far better to think about utilizing one before you begin. Opportunities are you might need a professional plumber to make tube connections.
This write-up will certainly assist you set up a new bath tub in your washroom if you have currently acquired a brand-new bathtub and also do not need to change the setup of your previous water system pipes.
Your devices as well as material list must make up the following:

 

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Tape Measure


• Pipe Caps


 

Preparing for the Installment

To start with, the supporting frame supplied with the bathroom must be fitted (if needed) according to the producer's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to ensure that if the faucet features a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets system to prevent strain on the bathtub.
Fit the adaptable faucet ports to the bottom of the two taps using 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you use every one of the provided washers.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to now prepare to be suited its final position.

 

 

Removing Old Taps

If you require to replace old taps with brand-new ones as a part of your installment, after that the first thing you ought to do is disconnect the water. After doing so, activate the taps to drain any kind of water continuing to be in the system. The process of getting rid of the existing faucets can be rather problematic as a result of the restricted access that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a towel prepared for the remaining water that will certainly come from the pipelines. When the supply pipes have actually been removed, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming throughout this process. Once the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any old securing compound.
Prior to carrying on to fit the new taps, contrast the pipe connections on the old faucets to the new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.

 

 

Installing the Bath tub

Utilizing the two wood boards under its feet, place the bath tub in the needed position. The wood boards are valuable in equally spreading the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four tiny factors.
The next objective is to ensure that the tub is leveled all round. This can be achieved by inspecting the spirit level and also adjusting the feet on the bath tub until the level reads degree.
To install faucets, fit the bottom of the outermost flexible faucet connector to the proper supply pipe by making a compression sign up with; after that do the exact same for the various other tap.
Activate the water supply and also check all joints as well as brand-new pipework for leaks and also tighten them if necessary. Fill up the bathtub and additionally check the overflow electrical outlet and also the typical electrical outlet for leaks.
Lastly, deal with the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bathtub must wait till the bathtub has actually been made use of at least once as this will certainly resolve it into its final placement.

 

 

Suitable New Taps

If the tails of the new faucets are plastic, after that you will need a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and also the other end offers a link to the current supply pipelines.
If you require to fit a monobloc, then you will require decreasing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the installing hole in the bath/basin making sure that the washing machines remain in place between the tap as well as the sink. Protect the faucet in position with the supplier given backnut. Once the tap is securely in place, the supply pipes can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical faucet ports. The previous kind must be connected to the tap ends first, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.

 

 

Tiling Around the Bath tub

In the location where the bathroom fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate enough to break a rigid seal, causing the water to penetrate the wall in between the bathroom as well as the tiling, causing issues with moisture as well as possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your fixtures and installations. They are marketed in tubes and also cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of soaked newspaper or soft rope. Remember to always fill the bathtub with water prior to securing, to permit the motion experienced when the bathtub is in use. The sealant can crack rather very early if you do not think about this activity prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally quickly offered on the market. It is advisable to fit the floor tiles utilizing water-resistant or waterproof glue and also grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

I'm certainly very interested in How to Install a Bathtub Yourself and I hope you liked our blog entry. Do you know about another person who is in the market for the subject? Do not hesitate to promote it. We love reading our article about A Step-by-Step Guide to Installing a Bathtub.

Visit Our Site